How-To: Clean The Section Of A Pelikan Demonstrator

Pelikan M200 Clear DemoWith a new Pelikan demonstrator due out in a few weeks, I thought now might be a good time to revisit how to best clean one.  The endearing thing about demonstrators is that they put the inner workings of the pen on display, warts and all.  Perhaps that is why the demonstrator is such a polarizing model amongst fountain pen enthusiast.  No matter what side of the debate you come down on, it’s undeniable that cleaning this type of pen can be a real challenge.  You can see every drop of residual ink and even more disturbing, every stain left behind.  Thankfully, good pen upkeep can help to avoid this type of permanent staining.  In addition to the usual pen maintenance issues that we all face, there is one exceedingly frustrating area on Pelikan demos that is particularly troublesome to clean.  That area would be the section which, no matter how much you may rinse or swab, simply won’t come clean.  With Pelikan’s demos, there is a little trick to be learned here which can make your cleaning woes a thing of the past.  Due to the design, there is a little lip on the inside of the section where the threads are located.  The area behind that lip will collect ink as you fill and use your pen.  It is not readily noticeable until you try to flush the pen clean.  Thankfully, it’s easy to remedy if you know what to do.  Read on to learn how to get that residual ink flushed out of the section.

**NOTE: The procedure outlined below will walk you through how to clean the section of a Pelikan demonstrator fountain pen.  If you are looking for an overview of how to clean a Pelikan fountain pen in general, please check out my article, How-To: Clean a Pelikan Fountain Pen.


What You’ll Need:

  1. Room temperature tap or distilled water
  2. A 5 or 10cc syringe with a blunt needle
  3. Paper towels, cloth, or similar
  4. A dilute (~1:10) ammonia solution (optional)
  5. Cotton swabs (preferably safety swabs)


USE FOR: All modern Pelikan demonstrator pens in both the Souverän and Classic lines

  1. Empty the barrel of ink and clean as you normally would.  Follow the link above for a tutorial on general Pelikan pen maintenance.
  2. When you are satisfied that the pen is clean, carefully remove the nib if you have not already done so and set aside.
    1. Unscrew and remove the cap from the pen thereby exposing the nib and feed.
    2. Placed the feed in the crook of the index finger on your non-dominant hand with the tip of the nib pointing towards the ground.
    3. Take the thumb of that same hand and apply pressure to the top of the nib, thereby preventing the nib from shifting on the feed.
    4. Now, with your dominant hand, turn the BARREL counterclockwise to unscrew the nib from the section (the nib itself should never move in your hand).
  3. Fill your syringe with water
  4. Place the tip of your blunt needle just inside the section.  Walk it down the inside of the wall of the section to where the nib threads start.  You will feel a lip there which is where you will rest your needle.
  5. Depress the plunger on the syringe such that water is being flushed along the wall of the section behind the lip.  In 1-2 syringes, you should be able to flush all of the residual ink out of the section
  6. If significant staining remains due to a particularly stubborn ink, consider using a dilute ammonia solution such as JB’s Pen Flush. 
  7. Once rinsed thoroughly, allow the pen to air dry.   You can use a towel or cotton swab to wick excess moisture.
  8. Replace the nib, employing the reverse of the above instructions.



Special Considerations:

  • If your tap water is very hard, meaning that there is a high mineral content in the water, mineral deposits can be left behind when the water evaporates.  For this reason, I favor the use of distilled water (specially prepared to remove chemicals and minerals) over tap.  Distilled water is cheap and readily available in 1 gallon jugs at any grocery store.  

Pelikan M200 Clear Demo and Edelstein Topaz

*I am not an expert in pen maintenance and make no claims to be one.  I am an enthusiast and hobbyist.  If you have any concerns or doubts, you should seek out further assistance elsewhere.  Anyone following the above procedures do so at their own risk and I am not liable for any damage that may be incurred to the pen, nib, or cap.

17 responses

  1. I discovered this method by mistake when I bought an M400 nib for my M200 Clear Demonstrator. When I was changing the nib, I though, well, I’ll clean the pen. I found using the piston too slow to pull water in and out (being the impatient person I am). So I just got my syringe and went to town. Happened upon that place in the section and saw ink and flushed it out. I’m glad you wrote this article; it will help lots of people who may not have happened upon this method before. While I’m guilty of not cleaning a pen maybe as often as I should, when I do clean it, I want it to be totally clean.


    • It’s not an intuitive things so it’s serendipity that you came across it. Like you, when a pen is supposed to be clean, I need it totally clean. Ink in the section like that would kill me.


  2. Thanks Joshua. I have a blue demonstrator M205 and had noticed that after flushing, there was still some ink residue trapped between the walls of the grip section, that could not easily be wiped off from inside or outside. Also, the “section” does not separate from the barrel. I will try using the syringe, as a mini pressure-jet cleaner and that should do it!


    • The syringe is the only way that I’ve figured out how to address this problem so far. It should get your blue demo M205 back to like new condition. Good luck.


  3. Thank you for the video!

    It could also be really practical to show those who wonder why their “cleaned” pen shows weird ink-mixing. It is somewhat hard to explain to people that there is that “pocket” or gap within the section walls especially in every other than the clear models. Some people might not even believe you, yet our flock is all built the same.

    I am sure in the future I will direct others more than once to your video to show where the ink really hides.

    Liked by 1 person

  4. I have a M1000 Demonstrator and to get the section clean I remove the nib unit, fill the barrel with distilled water right to the top and let it sit upright for a day. The capillary action frees the trapped ink in the glued section and once diluted it is easily flushed.


  5. Thank you for sharing this technique, it helped clean out the ink trapped in my M805 demonstrator. It looks like there’s also ink trapped between the section and the metal ring at the (front) end of the section. Do you have any suggestions on how I can clean that out?


Leave a Reply to dannytang Cancel reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: